Kontakt oss
Litex Membrane Board
No, Litex Membrane Board must never be coated with liquid membrane. The board is both watertight and vapour-tight, and is ready for tiling straight away.
Other wet room boards with a cement coating are vapour-permeable and must be coated with liquid membrane on external walls and on walls facing bedrooms and other cold rooms to achieve sufficient vapour resistance.
We recommend combining Membrane Boards on the walls with the Membrane Sheet system or PVC Sheet Membrane on the floor. You can combine them with liquid membrane, provided the products are compatible.
Take the number of linear metres of wall in the bathroom and divide by 0.6. This gives you the number of boards you need (based on a ceiling height of 2.44 m). Linear metres/0.6 = number of boards.
20 mm or thicker.
No, the core material in Litex Membrane Board withstands a load of more than 30 tonnes per m². The difference is that the surface of Litex Membrane Board never cracks, unlike a cement-coated wet room board.
As a general rule, the plastic sheeting should be removed. If you are in doubt, contact technical support.
25–30 cm along the joint. That means 10–15 screws per board. On a solid substrate, spot-bond the middle of the board with Litex Mounting Adhesive so that you only screw along the joint. Follow the table in the installation guide.
All Litex Membrane Boards are 244 x 60 cm and come in thicknesses of 13, 20, 30 and 50 mm
It depends on the screed, the reinforcement and the substrate. As a general rule, on stable timber joists it must be at least 20 mm.
Yes, approx. 10–15% better than standard mineral insulation of the same thickness. The boards have a thermal conductivity of 0.033 W/mK.
No.
The board has a pull-off strength of at least 300 kg per 10 x 10 cm tile
Cut the board tight to the frame and seal the transition with Litex Mounting Adhesive, or use our self-adhesive tape.
If you have a cold loft above the bathroom, you can install Litex Membrane Board on the ceiling as a vapour barrier. For a smooth surface, you can fill and sand the boards before painting them in the colour of your choice.
Yes, but you get a much safer and faster solution by using our membrane tape. See here.
You seal the joints quickly and easily using our unique self-adhesive tape
Make sure the PVC sheet membrane has an upstand of 8 cm or more. Then apply 1 bead of adhesive to the upstand before you install the membrane boards. When all the boards are installed, apply a bead of adhesive in the angle between the floor membrane and the wall board.
Apply Litex Mounting Adhesive in 2–3 circles around the pipe, then use a filling knife to spread the adhesive over the area that will be covered by the collar. Fit the collars and use the filling knife to press out excess adhesive, working in towards the centre of the collar.
Yes, the boards are also approved for use on floors.
The substrate must be primed before installation. Once this is done, you have several options:
- On an even substrate, use a 13 mm board, fully bonded with tile adhesive applied with a notched trowel.
- On an uneven substrate, use a thicker board and apply the tile adhesive in spots.
- You can also apply 3 finger-width beads of low-expansion foam adhesive to the board.
- If the wall is out of plumb, use a 20 mm board or thicker, installed with tile adhesive applied in a pattern like the five on a dice. Approx. 10–12 spots per board.
Litex Membrane Sheet System
The membrane sheet must not be coated, as it is already watertight and vapour-tight in accordance with TEK17.
The working time is normally 45 minutes, but by following the instructions for use you can extend this to 1 hour.
On all solid substrates. When installing on plasterboard or absorbent substrates, the surface must be primed first. Dry concrete surfaces should be dampened before installation. Note that on floors there must be no deflection in the substrate.
No. The collars have a smooth surface on both sides, so you must use Litex Mounting Adhesive.
Yes, the day after installation you can tile directly on top of the membrane sheet.
You need a mixer, notched trowel, wallpaper smoother, brush, utility knife, grooved roller and a cloth
Yes, we recommend this for walls. Use a long-pile disposable roller. You will save both time and adhesive compared with using a notched trowel.
Adhesive consumption with a roller is approx. 1 kg per m². Make sure there is enough adhesive on the wall. Check by pulling back a corner of the sheet to confirm that the amount is sufficient.
Time required: 2–3 minutes per m² when applying adhesive with a roller.
For floors we recommend a notched trowel, as floors often have larger irregularities that a notched trowel handles better.
Consumption with a notched trowel: 1.5 kg per m²